{"product_id":"ac-infinity-thermoforge-t3","title":"AC Infinity Thermoforge T3 Ducted Ceramic Heater","description":"\u003cp\u003eThe AC Infinity Thermoforge T3 Ducted Ceramic Heater is the compact model in the Thermoforge family, built to hold a grow tent at a target temperature or VPD through cold nights and unheated rooms. AC Infinity rate it for tents up to 1.5 x 1.5 m (5 x 5 ft); that rating assumes a sealed, well-insulated space, and in a cold room it is an ideal-conditions ceiling rather than a promise. It is also the complete in-box option of the pair: where the larger \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-thermoforge-t7\" target=\"_blank\" title=\"AC Infinity Thermoforge T7 Ducted Ceramic Heater\" rel=\"noopener\"\u003eAC Infinity Thermoforge T7 Ducted Ceramic Heater\u003c\/a\u003e connects to separate 100 mm ducting, the T3 carries its own built-in hose and a detachable extension, so the heater body stands outside the tent and ducts warmth through the lowest port with nothing further to buy.\u003c\/p\u003e\n\u003cp\u003eInside the tower housing, three PTC ceramic plates generate the heat. PTC ceramic is flameless and self-regulating, with no exposed glowing element, and pulse-width modulation steps its output across ten heat levels rather than crudely switching on and off; a ten-level fan function moves unheated air through the same body. A corded thermal-alloy sensor probe plugs into the 3.5 mm jack at the rear and routes to canopy height, feeding an onboard LCD controller that runs Auto low-temperature triggering, a VPD mode accounting for ambient temperature, humidity and leaf temperature with leaf offset and calibration settings, plus timer and cycle programs. Warm air leaves through the built-in hose, which extends from 25.0 to 70.0 cm (9.84 to 27.55 in), and the included duct extension hose reaches from 50.0 to 140.0 cm (19.68 to 55.11 in) for longer runs. The unit measures 29.2 x 15.1 x 30.8 cm (11.49 x 5.94 x 12.12 in), draws 530 W at 240 V \/ 50 Hz, and carries the RCM mark under SAA approval EESS-250152-0.\u003c\/p\u003e\n\u003cp\u003eConnecting the included male-to-male UIS cord to a controller such as the \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-ai-environmental-controller\" target=\"_blank\" title=\"AC Infinity Ai+ Environmental Controller\" rel=\"noopener\"\u003eAC Infinity Ai+ Environmental Controller\u003c\/a\u003e hands over full automation: the controller overrides the onboard settings, reads from its own sensor probe, and schedules heat alongside fans, lights and a humidifier such as the \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-cloudforge-t3-v2-humidifier\" target=\"_blank\" title=\"AC Infinity Cloudforge T3 V2 Humidifier\" rel=\"noopener\"\u003eAC Infinity Cloudforge T3 V2 Humidifier\u003c\/a\u003e for complete VPD control. The box includes the heater, sensor probe, UIS extension cord, four probe mounts, four hook-and-loop ties and the duct extension hose. Operating range is -10 to 60°C (14 to 140°F) at 30 to 85% relative humidity, though AC Infinity advises placing the unit inside a tent only where humidity stays at or below 65%, and it is intended for dry indoor locations only. Its extendable hoses reach up to 140.0 cm (55.11 in) from the unit, letting the heater stand clear of the canopy while its Auto or VPD trigger holds the tent at target through the coldest part of the night.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eNOTE:\u003c\/strong\u003e keep at least 0.9 m (3 ft) of clearance on all sides from walls, fabric and flammable materials, and never cover or obstruct the heater. Plug it directly into a wall outlet; never use an extension cord, power board or surge protector. Use only in dry indoor locations, upright on a stable surface; a fail-safe pauses heating if the unit falls or tilts past 15 degrees, and overheat protection cuts heating at 90°C (194°F) internally or when the sensor probe reads above 60°C (140°F). Surfaces become hot in use; move the heater by its handle.\u003c\/em\u003e\u003c\/p\u003e","brand":"AC Infinity","offers":[{"title":"550 W","offer_id":45839380545694,"sku":"819137024489","price":239.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0709\/5261\/6094\/files\/AC_Infinity_Thermoforge_T3.png?v=1784690727","url":"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-thermoforge-t3","provider":"Hydro Oasis","version":"1.0","type":"link"}