{"product_id":"ac-infinity-thermoforge-t7","title":"AC Infinity Thermoforge T7 Ducted Ceramic Heater","description":"\u003cp\u003eThe AC Infinity Thermoforge T7 Ducted Ceramic Heater is the high-output model of the Thermoforge pair, the model AC Infinity rate for spaces up to 3 x 3 m (10 x 10 ft), picking up where the compact \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-thermoforge-t3\" target=\"_blank\" title=\"AC Infinity Thermoforge T3 Ducted Ceramic Heater\" rel=\"noopener\"\u003eAC Infinity Thermoforge T3 Ducted Ceramic Heater\u003c\/a\u003e runs out of reach. That rating assumes a sealed, well-insulated space; heating is the hardest job in a cold-climate grow, and in an uninsulated tent or a cold room practical coverage is considerably smaller - treat the figure as an ideal-conditions ceiling, not a promise. In place of a built-in hose it is a ducted box with twin 100 mm (4 in) ports, plumbing into standard ducting to run either an open loop that delivers heated fresh air, or a closed loop that recirculates the space's own air so already-warmed air is never vented away. It is also the only model in the family with a ten-level fresh-air intake and the Adaptive AI heat setting.\u003c\/p\u003e\n\u003cp\u003eInside the 22.0 x 17.8 x 25.4 cm (8.66 x 7.00 x 10.00 in) housing, individual PTC ceramic plates deliver up to 1000 W at 240 V \/ 50 Hz. Like the rest of the family it heats on flameless, self-regulating PTC ceramic, with pulse-width modulation stepping output across ten true heat levels, while the separate ten-level intake draws in cooler outside air when the space needs airflow rather than warmth. A corded precision sensor probe feeds the onboard controls, which run On, Auto low-temperature, VPD, timer and cycle modes through a button interface with indicator lights; AC Infinity states the Adaptive AI setting analyses the room's climate patterns, anticipates temperature spikes and adjusts heat levels dynamically as it learns. The housing is flame retardant, tip-over alarms and overheat protection with automatic restart back the heating plates, and the unit is RCM marked under the same SAA approval (EESS-250152-0) that covers the whole Thermoforge family.\u003c\/p\u003e\n\u003cp\u003eDucting is not included: the heat-rated companion for the T7 is the \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-thermal-resistant-hose\" target=\"_blank\" title=\"AC Infinity Thermal Resistant Hose\" rel=\"noopener\"\u003eAC Infinity Thermal Resistant Hose\u003c\/a\u003e, the Thermoforge-specific duct moulded to take sustained heater output that softens standard PVC-shelled ducting. Over the UIS platform a controller such as the \u003ca href=\"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-ai-environmental-controller\" target=\"_blank\" title=\"AC Infinity Ai+ Environmental Controller\" rel=\"noopener\"\u003eAC Infinity Ai+ Environmental Controller\u003c\/a\u003e folds the T7 into whole-room automation, overriding the onboard settings with its own sensor probe and programs. Operating range is -10 to 60°C (14 to 140°F) at 30 to 65% relative humidity, a narrower humidity window than the T3's 85%, and the unit suits dry indoor locations only. Its dual ports and closed-loop capability let a single heater serve a sealed room without exhausting the air it has already heated, holding the space at target through winter nights.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eNOTE:\u003c\/strong\u003e keep at least 0.9 m (3 ft) of clearance on all sides from walls, fabric and flammable materials, and never cover or obstruct the heater. Plug it directly into a wall outlet; never use an extension cord, power board or surge protector. Use only in dry indoor locations, upright on a stable surface; a fail-safe pauses heating if the unit falls or tilts past 15 degrees, and overheat protection cuts heating at 90°C (194°F) internally or when the sensor probe reads above 60°C (140°F). Surfaces become hot in use; move the heater by its handle.\u003c\/em\u003e\u003c\/p\u003e\n\u003cp style=\"text-align: center;\"\u003e\u003ciframe width=\"1396\" height=\"785\" src=\"https:\/\/www.youtube.com\/embed\/4RDlJkWojJ8\" title=\"\"\u003e\u003c\/iframe\u003e\u003c\/p\u003e","brand":"AC Infinity","offers":[{"title":"1000 W","offer_id":46843735146654,"sku":"819137024502","price":269.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0709\/5261\/6094\/files\/AC_Infinity_Thermoforge_T7.png?v=1784690747","url":"https:\/\/www.hydrooasis.com.au\/products\/ac-infinity-thermoforge-t7","provider":"Hydro Oasis","version":"1.0","type":"link"}