Visit Us In-Store: 2/322 Hobart Rd, Youngtown TAS
AC Infinity Suncore Heat Mat
The AC Infinity Suncore H3 Heat Mat is a 20 W far-infrared seedling heat mat supplied with its own inline digital heat controller, warming the root zone where germination speed and cutting strike are actually decided. Within AC Infinity's SUNCORE range the H designation is the distinction that matters: where the mat-only A-series runs flat out whenever it is plugged in, the H3's included controller holds an exact setpoint, powering the element only while the sensed temperature sits below it. Placed beneath a propagation cover such as the AC Infinity Humidity Dome, its bottom warmth accelerates germination and drives humidity up quickly under the canopy.
The mat is a quad-layer PVC laminate just 2.48 mm (0.09 in) thick, heated by a far-infrared film lining rather than wire coils, so warmth spreads evenly across the full 25.4 x 52.7 cm (10 x 20.75 in) surface instead of concentrating into scorching lines. Sealed seams and a sealed cord connection earn the mat an IP67 rating, meaning watering spills wipe straight off, though it must never be immersed. AC Infinity rates the mat to lift the rooting area approximately 5 to 11 °C (10 to 20 °F) above ambient, settling into a steady 27 to 31 °C (80 to 87 °F) band in typical rooms. The controller sits inline on the 152.4 cm (60 in) cord in a compact 8.0 x 4.5 cm (3.14 x 1.77 in) body, with a backlit display showing sensed and set temperatures side by side, up and down buttons spanning a 0 to 50 °C (32 to 122 °F) range, a switchable °C or °F readout, and screw mounts for fixing it to a wall.
The mat matches the standard 1020 tray footprint and pairs almost exactly with the XL Humidity Dome tray at 54.5 x 28.4 cm. The box includes the mat, the inline controller, a water-resistant nylon storage cover with drawstring closure, two machine screws and two wood screws for wall mounting. Where a seed packet gives no figure, the manual suggests holding 18 to 24 °C (65 to 75 °F), and a crop temperature chart is printed on the mat face itself, while an independent reading at tray level from an AC Infinity CLOUDCOM B Hygrometer confirms what seedlings are actually experiencing. AU-supplied units run on 240 V. The included controller cycles the mat thermostatically against its setpoint, holding a set root-zone temperature through cold nights without overheating a tray on warm afternoons.
NOTE: place the mat on a flat, well-drained surface free of standing water and sharp objects. Never position it inside a tray, cover it directly with soil or growing media, or lay heat-insulating materials over it, as trapped heat can build dangerously. The mat is rated IP67 for spills and wipe-downs but must not be immersed in water.
A 20 W far-infrared seedling heat mat with its digital controller included, holding an exact root-zone temperature through germination and cutting strike.
Controller Included
Inline digital controller displays sensed and set temperatures, cycling the mat to hold an exact target.
Far-Infrared Warmth
Film element spreads gentle, even heat across the whole mat with no wire hot spots.
IP67 Waterproof
Quad-layer PVC with sealed seams and cord connection wipes clean after watering spills.
Back-Order
2 Years warranty · 30-day returns
Secure checkout
with
Buy with confidence
-
Talk to a real grower
Not sure it suits your setup? Call our Youngtown team on
0481 526 666.
-
Price Beat Guarantee
Found it cheaper elsewhere? We'll
beat any competitor's price by 5%.
-
Tasmania's own hydroponics shop
Buy online & collect in-store at 2/322 Hobart Rd, Youngtown TAS, usually within the hour.
AC Infinity Suncore Heat Mat
Key Highlights
expand_more
Key Highlights
- Inline digital heat controller included: backlit display of sensed and set temperatures with a 0 to 50 °C (32 to 122 °F) setting range
- Rated by AC Infinity to lift the rooting area 5 to 11 °C (10 to 20 °F) above ambient, settling at a steady 27 to 31 °C (80 to 87 °F)
- 25.4 x 52.7 cm (10 x 20.75 in) footprint matches a standard 1020 seedling tray
- Draws a maximum of 20 W; AU-supplied units run on 240 V
- Includes seedling mat, inline controller, water-resistant nylon storage cover and wall-mounting screws
- Crop temperature chart printed directly on the mat face for quick reference
- 2 year manufacturer warranty
Directions for Use
expand_more
Directions for Use
- Place the mat on a flat, well-drained surface free of standing water and sharp objects.
- Sit the seedling tray or propagation dome on top of the mat; never place the mat inside a tray or cover it directly with growing media.
- Connect the inline controller and plug into a 240 V outlet.
- Set the target temperature with the up and down buttons; hold both together to switch between °C and °F.
- If the seed packet gives no figure, hold 18 to 24 °C (65 to 75 °F), or consult the crop chart printed on the mat face.
- Let the controller cycle the mat automatically; it heats only while the sensed temperature is below the setpoint.
- To wall-mount the controller, fix it with the included screws; hold the power button for 10 seconds to restore factory settings if needed.
- After use, unplug the mat, wipe it clean and roll it into the included storage cover.
Technical Specifications
expand_more
Technical Specifications
- Product Model SUNCORE H3 (AC-SMH3)
- UPC Code 819137024540
- Power 20 W maximum
- Voltage 240 V (AU supplied)
- Temperature Rise Approximately 5 to 11 °C (10 to 20 °F) above ambient, per AC Infinity
- Controller Setting Range 0 to 50 °C (32 to 122 °F), switchable °C/°F
- Heating Element Far-infrared film lining
- Waterproof Rating IP67 (do not immerse)
- Mat Material Quad-layer PVC with sealed seams and sealed cord connection
- Mat Size 25.4 x 52.7 cm (10 x 20.75 in), standard 1020 tray footprint
- Mat Thickness 2.48 mm (0.09 in)
- Controller Size 8.0 x 4.5 cm (3.14 x 1.77 in)
- Cord Length 152.4 cm (60 in)
- Included Seedling mat x1, inline digital heat controller x1, storage mat cover x1, machine screw x2, wood screw x2
- Certifications cULus Listed (E518635), MET, CE, RoHS
- Warranty 2 Years
Resources
Shipping & Returns
expand_more
Shipping & Returns
Check delivery options for the currently selected item and quantity.
Estimate is for this item and quantity only. Final whole-order freight is confirmed at checkout.
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
To start a return, you can contact us at info@hydrooasis.com.au
If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at info@hydrooasis.com.au.
Colour: H3
