AC Infinity UIS USB C Extension Cable
Extra reach or a tighter plug angle is the job of the AC Infinity UIS USB C Extension Cable family, carrying power and control signals between a UIS controller and compatible AC Infinity equipment. With length shared, selection comes down to what each end must meet and whether the cable must turn sharply beside a housing or panel. The family covers direct controller-to-device runs and extension of a device's existing lead, with connector arrangements, controller support and dimensions kept in Technical Specifications.
AC Infinity publish the same layered construction across the range: copper conductors and a steel strength member surrounded by precision insulation, an aluminium inner shield and a rubber TPU outer shield. The shielding is useful in equipment-dense grow spaces, although the manufacturer does not publish a shielding-performance figure. UIS also carries more than a simple on-and-off command. A compatible device can power the controller while the same cable carries the level and operating mode used for triggers, timers, cycles and schedules.
Available plug arrangements cover practical jobs: keeping a connection close to a housing or panel, extending a factory-fitted device lead without replacing it, or joining female UIS ports directly. AC Infinity note that a suitable controller cord is normally included with UIS-compatible devices, so an additional cable is typically purchased for extra reach, replacement or tighter clearance rather than basic operation. The correct arrangement must be checked before purchase because the cable ends are not interchangeable.
NOTE: UIS is AC Infinity's proprietary USB-C-shaped connection and is not intended for USB data transfer or charging ordinary devices. Controller AI+ support differs by cable: AC Infinity list full advanced-function support for the female-to-male version, limited device-identification and advanced functions for the right-angle version, and no published Controller AI+ statement for the straight male-to-male version.
An extra 3.05 m between your device and your controller.
Fits Either Device End
A cord for male ended leads and female ports.
Fits Tight Clearances
The L shaped cord exits flat against a housing.
Shielded Against Interference
Aluminium and TPU layers around the copper conductors.
Back-Order
Verified by Hydro Oasis
30-day returns
Secure checkout
with
Buy with confidence
-
Talk to a real grower
Not sure it suits your setup? Call our Youngtown team on
0481 526 666.
-
Price Beat Guarantee
Found it cheaper elsewhere? We'll
beat any competitor's price by 5%.
-
Tasmania's own hydroponics shop
Buy online & collect in-store at 2/322 Hobart Rd, Youngtown TAS, usually within the hour.
AC Infinity UIS USB C Extension Cable
Key Highlights
expand_more
Key Highlights
- Three models on one page: AC-EXQ9 female-to-male, AC-EXR9 straight male-to-male and AC-EXS9 right-angle male-to-male, all 3.05 m (120 in / 10 ft)
- The AC-EXQ9 is the only one of the three that couples onto a lead already in place: AC Infinity describe it as a cable to extend the length of an existing connection cable between UIS controllers, compatible devices and splitter hubs
- Of the three, only the AC-EXQ9 carries AC Infinity's full Controller AI+ statement; the AC-EXS9 is listed with function limits and the AC-EXR9 has no published AI+ statement at all
- The straight AC-EXR9's published device list does not include the Cloudforge, Ionframe, Terraform or Thermoforge series, which the other two cords both name
- AC Infinity's Controller 69 Pro manual lists a male-to-male extension cord as supplied with UIS-compatible devices, so the AC-EXR9 buys extra length and the AC-EXS9 buys right-angle clearance, not a missing part
- Covered by AC Infinity's 2 year warranty
Directions for Use
expand_more
Directions for Use
- Choose the cable by what each end has to meet: a female-to-male cable couples onto the male plug of a lead already fitted to a device or splitter hub, while a male-to-male cable runs a controller port straight to a device port.
- On the L-shaped cable, plan for the right-angle plug to sit at the device, so the cord exits flat against its housing, and the straight plug at the controller.
- Plug the first connector into a UIS port on the controller and push it home until it seats at its 0.6 cm (0.23") depth.
- Route the cord clear of the power cords of HID grow light ballasts (MH, HPS, CMH or CHPS), which AC Infinity's Controller 69 Pro manual identifies as a source of radio frequency interference where the ballast carries no electromagnetic shielding.
- Connect the far end to the device's female UIS port, or, with the female-to-male cable, receive the device lead's male plug into the female head.
- Where a splitter hub shares one controller port, plug the primary device into Port 1; every other device on that splitter follows Port 1's programming, per AC Infinity's Controller 69 Pro manual.
- Plug the device's own mains cord into a wall outlet to power both the device and the controller, then set the port's level, triggers, timers or schedule at the controller or in the AC Infinity app.
Technical Specifications
expand_more
Technical Specifications
Female/Male / Straight
- Product Model AC-EXQ9
- UPC Code 819137022225
- Cable Type UIS extension cord (inline coupler for an existing lead)
- Design Feature Water-resistant gasket
- Connector Ends UIS female connector to UIS male connector (USB-C style)
- Controller AI+ Support Fully compatible, including all device identification and advance functions
- Compatible Controllers Controller AI+, Controller 69 Pro, Controller 69 Pro+, Controller 63
- Compatible Devices Cloudforge, Cloudline, Cloudlift, Cloudray, Cloudway, Airlift, Airblaze, Airtitan, Ionframe, Ionboard, Ionbeam, Terraform and Thermoforge series
Male/Male / Straight
- Product Model AC-EXR9
- UPC Code 819137023666
- Cable Type UIS extension cord (controller to device)
- Connector Ends UIS male connector to UIS male connector (USB-C style)
- Controller AI+ Support Not published by AC Infinity for this model
- Compatible Controllers Controller 69, Controller 69 Pro, Controller 63
- Compatible Devices Cloudray, Cloudline Lite, Cloudway S, Airlift, Airblaze S, Airtitan S, Iongrid, Ionboard and Ionbeam series
Male/Male / L Shaped
- Product Model AC-EXS9
- Cable Type UIS extension cord (controller to device)
- Design Feature L-shaped, with a ribbed strain-relief boot at the right-angle end
- Connector Ends UIS male connector to UIS male L-connector (USB-C style)
- Controller AI+ Support Compatible, but does not support certain device identification and advance functions
- Compatible Controllers Controller 69 Pro, Controller 69 Pro+, Controller 63; Controller AI+ with the limitation above
- Compatible Devices Cloudforge, Cloudline, Cloudlift, Cloudray, Cloudway, Airlift, Airblaze, Airtitan, Ionframe, Ionboard, Ionbeam, Terraform and Thermoforge series
All Models
- Construction Durable steel wire, premium copper wire, precision insulation, aluminium inner shield, rubber TPU outer shield
- Colour Solid black
- Cable Length 3.05 m (120 in / 10 ft)
- UIS Depth 0.6 cm (0.23")
- Warranty 2 Years
Shipping & Returns
expand_more
Shipping & Returns
Check delivery options for the currently selected item and quantity.
Estimate is for this item and quantity only. Final whole-order freight is confirmed at checkout.
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
To start a return, you can contact us at info@hydrooasis.com.au
If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at info@hydrooasis.com.au.
Size: Female/Male, Colour: Straight
