Visit Us In-Store: 2/322 Hobart Rd, Youngtown TAS
SeaHawk Propagation Tent
Cuttings, seedlings and early vegetative plants gain a dedicated warm, humid zone inside the SeaHawk Propagation Tent before moving to a full-size grow tent for routine early-stage growing work. The family includes an open-floor format for a small propagation setup and a larger racked format for running trays on two levels. The choice comes down to floor layout and the number of tray levels, while exact dimensions, shelf arrangements, ports and access points are listed in Technical Specifications.
The cover uses a black woven outer fabric with reflective silver lining across the solid inner panels. A fine diamond-like texture scatters returned light rather than reflecting it as one hard beam, which suits the short working distances found in a propagation enclosure. Breathable intake areas are intentionally left permeable so replacement air can enter without a powered intake fan. Warm, moist air can then leave through the roof opening naturally or through ducted extraction when tighter temperature and humidity control is needed.
A push-fit metal frame supports the cover. Every pole must be fully seated into its corner or joiner before the fabric is fitted; a partly engaged connection changes the frame geometry, stretches seams and makes the zip harder to close. The removable floor tray is useful for catching splashes during watering, but it should be emptied and wiped rather than used to hold standing water. Nylon straps and hanging bars support the internal layout, while the larger model adds coated wire racks for the two shelf levels.
The tent itself does not include a propagation light, fan, tray, humidity dome or heat mat. Those parts need to be selected around the chosen layout, with enough vertical clearance left between each shelf, the plants and the light. Passive intake also means the enclosure is not sealed. It will not maintain strong negative pressure or contain odour like a fully ducted grow tent, and neither model has a drain outlet. The roof port can accept extraction ducting when passive breathing is no longer enough to manage heat or humidity.
SeaHawk provides a 12-month manufacturer warranty for manufacturing and material defects, with zips covered for three months. Incorrect setup, stretched seams, condensation, mould, wear and damage from misuse are excluded, so the frame and cover should be inspected during the first assembly.
NOTE: This is an enclosure, not a complete propagation kit. Light, fan, trays, domes and heating equipment are sold separately. Keep electrical connections above any runoff, remove standing water promptly and do not expect the breathable intake panels to provide the containment of a sealed grow room.
Create the perfect environment for your cuttings and seedlings!
Ventilates Without A Fan
A permeable intake and roof vent exchange air.
See In Without Opening
A viewing window on both models shows the cuttings.
Sized To The Batch
The smaller holds one tray, the larger two per shelf.
Low Stock - 4 available
Low Stock - 4 available
Verified by Hydro Oasis
30-day returns
Secure checkout
with
Buy with confidence
-
Talk to a real grower
Not sure it suits your setup? Call our Youngtown team on
0481 526 666.
-
Price Beat Guarantee
Found it cheaper elsewhere? We'll
beat any competitor's price by 5%.
-
Tasmania's own hydroponics shop
Buy online & collect in-store at 2/322 Hobart Rd, Youngtown TAS, usually within the hour.
SeaHawk Propagation Tent
Key Highlights
expand_more
Key Highlights
- 0.75 m model carries one 175 mm (6.9") roof outlet vent, one 175 mm (6.9") side intake port and three 100 mm (4") cable ports
- 1.2 m model carries one 225 mm (8.9") roof outlet vent, one 100 mm (4") cable port and a full-height breathing intake panel down its left wall
- Roof outlet takes 150 mm (6") ducting on the 0.75 m model and 200 mm (8") on the 1.2 m model
- 1.2 m model ships with eight steel wire racks and eight hanging bars, six carrying two shelf levels and two left at the top of the frame for a light
- Detachable splash tray and nylon fabric straps supplied with both models
- 12 month warranty on the tent against material and workmanship defects, and 90 days on the zippers
Directions for Use
expand_more
Directions for Use
- Check the box contents against the parts list before starting, and lay out the poles, connectors, hanging bars, tray and cover.
- Assemble the metal frame, pushing every pole fully home into its corner or connector. Tap fittings gently with a rubber mallet where they are tight. A pole left short makes the cover hard to fit and can stretch the seams enough to let light through.
- Unzip the zip systems on the cover all the way.
- On the 0.75 x 0.5 x 0.7 m model, place the roof neatly over all four corners of the top frame for a snug fit, then hang the three bars - one across the depth and two along the width - before going any further.
- On the 0.75 x 0.5 x 0.7 m model, slip the base section of the cover beneath the assembled bottom rails so it sits neatly around the frame corners and sides.
- On the 1.2 x 0.6 x 1.2 m model, start at the floor instead: fit the cover onto the four base corners with the door oriented so it opens from the bottom upwards, then slip the left and right sides over the frame, zipping the cover up little by little as it goes on.
- On the 0.75 x 0.5 x 0.7 m model, close the zip systems carefully, pushing the upright poles inwards at each corner as the zip passes.
- On the 1.2 x 0.6 x 1.2 m model, fit four steel wire racks onto three hanging bars at each of the two frame levels, adjusting the bars and racks flat and horizontal. The two remaining bars go at the top of the frame to hang a light from.
- Fit the floor tray and the nylon fabric straps in place, then zip the front door closed.
- Where extraction is wanted, feed ducting into the roof outlet vent and draw the sleeve closed around the duct - 150 mm (6") on the 0.75 x 0.5 x 0.7 m model, 200 mm (8") on the 1.2 x 0.6 x 1.2 m model. Running without a duct, leave the sleeve open so warm, moist air can leave through the roof vent.
- Clean and dry the tent before dismantling, then reverse the assembly sequence. Dismantle carefully and avoid stretching the seams, which is what keeps the cover light-tight.
- Store the cover folded flat and dry, with the poles, connectors and hanging bars kept together.
Technical Specifications
expand_more
Technical Specifications
0.75 x 0.5 x 0.7 m Model
- Product Model 8553
- UPC Code 744109815065
- Outlet Vent 1 x 175 mm (6.9") diameter, roof
- Intake Port 1 x 175 mm (6.9") diameter, left side wall
- Mesh Intake Panels 2, low on the right and left side walls
- Cable Ports 3 x 100 mm (4") diameter, one each on the right, rear and left walls
- Viewing Window 1, front panel
- Door 1, front, vertical centre zip
- Shelving None
- Hanging Bars 3, one across the depth and two along the width
- Drain Outlet None
- Dimensions 0.75 m W x 0.5 m D x 0.7 m H (30 x 20 x 28 in)
- Recommended Ducting 150 mm (6") at the roof outlet and the side intake port
1.2 x 0.6 x 1.2 m Model
- Product Model 4136
- Outlet Vent 1 x 225 mm (8.9") diameter, roof
- Air Intake Wall Full left side panel, breathable
- Cable Port 1 x 100 mm (4") diameter, right side wall
- Viewing Window 1, on the door panel
- Door 1, front, opens from the bottom upwards
- Shelving 8 steel wire racks over 2 levels
- Hanging Bars 8, six carrying the racks and two spare at the top of the frame for a light
- Drain Outlet None
- Dimensions 1.2 m W x 0.6 m D x 1.2 m H (47 x 24 x 47 in)
- Recommended Ducting 200 mm (8") at the roof outlet
All Models
- Outer Shell Black woven fabric; SeaHawk describe the range as manufactured using water-resistant materials
- Inner Lining Reflective silver film on the solid panels and the roof underside, described by Holland Forge as a light-proof ADF reflective material with a fine diamond-like surface; the air-intake panels are unlined
- Frame Push-fit metal poles into three-way corner connectors, with four-way cross connectors added on the 1.2 m model
- Cover Closure Full-length zip systems, opening completely for fitting
- Included Detachable splash tray and nylon fabric straps; the 1.2 m model also includes 8 steel wire racks
- Accessory Pouch None
- Australian Distributor Holland Forge Pty Ltd
- Warranty 12 months on the tent against defects in materials and workmanship with proof of purchase, and 90 days on the zippers
Resources
Shipping & Returns
expand_more
Shipping & Returns
Check delivery options for the currently selected item and quantity.
Estimate is for this item and quantity only. Final whole-order freight is confirmed at checkout.
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
To start a return, you can contact us at info@hydrooasis.com.au
If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at info@hydrooasis.com.au.
Size: 0.75 x 0.5 x 0.7 m
