Visit Us In-Store: 2/322 Hobart Rd, Youngtown TAS
AC Infinity Thermal Resistant Hose
The AC Infinity Thermal Resistant Hose is the dedicated exhaust duct for the Thermoforge T7 and S7 ducted grow heaters, carrying their heated output from the unit into the grow space so warmth lands where the canopy needs it rather than pooling around the heater. Standard ducting is not built for a heater's exhaust path - PVC-shelled flexible ducting melts where exhaust temperatures pass 80 C, and bare foil kinks and tears when repeatedly flexed hot - so this hose is moulded instead from thermal-resistant polypropylene that takes sustained heater output while its outer surface stays cooler to the touch, for hobby and professional growers running heat into tents through a Tasmanian winter.
The hose is formed as a continuous polypropylene concertina, and the pleated wall does two jobs at once. Folded, it packs to 0.7 m (2.3 ft) for storage and tight installs; drawn out, the pleats extend it to a full 2.4 m (8 ft), around four times its packed length, with no joins or seams for hot air to escape through. The same pleating makes the wall semi-rigid: bend it to an angle and it holds that angle, so a stream of warm air can be aimed at a cold corner or up under a canopy and stay aimed, without sagging or springing back. At the heater end a counter-clockwise threaded collar winds onto the exhaust port and locks against it, a positive mechanical seal that does not work loose as the hose expands and contracts through heating cycles. The polypropylene wall also insulates, so the hose can route past tent fabric, cabling and foliage without presenting a hot surface.
It fits the exhaust port of the Thermoforge S7 and T7 and is the heat-rated duct option for both; the heaters' 100 mm (4 in) intake side takes standard four-layer ducting instead. Its threaded collar and shape-holding wall deliver the T7's full 1000 W output to a precise point up to 2.4 m (8 ft) from the heater, through heating cycle after heating cycle.
NOTE: this hose suits the exhaust side of the Thermoforge S7 and T7 only - it is not compatible with their intake ports, which take standard 100 mm (4 in) four-layer ducting.
The dedicated heat-rated exhaust hose for the Thermoforge S7 and T7, extending 0.7 m to 2.4 m and holding its bend to aim warm air exactly where the grow needs it.
Takes Sustained Heat
Thermal-resistant polypropylene carries heater exhaust that would melt PVC-shelled ducting, and stays cooler outside.
Extends 0.7 m to 2.4 m
The seamless concertina wall packs to 0.7 m and draws out to 2.4 m, around four times its stored length.
Locks On, Holds Its Bend
A counter-clockwise threaded collar seals to the exhaust port, and the semi-rigid wall holds any angle you set.
Back-Order
Verified by Hydro Oasis
2 Years warranty · 30-day returns
Secure checkout
with
Buy with confidence
-
Talk to a real grower
Not sure it suits your setup? Call our Youngtown team on
0481 526 666.
-
Price Beat Guarantee
Found it cheaper elsewhere? We'll
beat any competitor's price by 5%.
-
Tasmania's own hydroponics shop
Buy online & collect in-store at 2/322 Hobart Rd, Youngtown TAS, usually within the hour.
AC Infinity Thermal Resistant Hose
Key Highlights
expand_more
Key Highlights
- Purpose-built exhaust hose for the Thermoforge S7 and T7 ducted grow heaters
- Thermal-resistant polypropylene takes sustained heater output that melts PVC-shelled ducting
- Outer surface stays cooler to the touch, safe past tent fabric and foliage
- Seamless concertina wall packs to 0.7 m (2.3 ft) and extends to 2.4 m (8 ft)
- Semi-rigid pleating holds any bend you set, keeping warm air aimed where you point it
- Counter-clockwise threaded collar locks a positive seal that survives heating cycles
- Exhaust side only - the heaters' 100 mm (4 in) intake takes standard four-layer ducting
Directions for Use
expand_more
Directions for Use
- Position the Thermoforge heater just outside or at the edge of the grow space.
- Wind the hose collar onto the heater's exhaust port, turning counter-clockwise until it locks and seals.
- Draw the hose out to length, up to 2.4 m (8 ft), and route it into the tent or room.
- Bend the hose to aim the warm air at a cold corner or under the canopy, and re-aim as the grow changes.
Technical Specifications
expand_more
Technical Specifications
- Model AC-DTH4-8
- UPC Code 819137025288
- Type Heater exhaust ducting hose
- Length 0.7 m (2.3 ft) packed, extends to 2.4 m (8 ft)
- Material Thermal-resistant polypropylene
- Connection Counter-clockwise threaded collar
- Compatibility Thermoforge S7 and T7 (exhaust port only)
- Warranty 2 years
Shipping & Returns
expand_more
Shipping & Returns
Check delivery options for the currently selected item and quantity.
Estimate is for this item and quantity only. Final whole-order freight is confirmed at checkout.
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused, with tags, and in its original packaging. You’ll also need the receipt or proof of purchase.
To start a return, you can contact us at info@hydrooasis.com.au
If your return is accepted, we’ll send you a return shipping label, as well as instructions on how and where to send your package. Items sent back to us without first requesting a return will not be accepted.
You can always contact us for any return question at info@hydrooasis.com.au.
